EASY Joint PRO
A tough jointing compound for patios, paths and driveways
- Perfect option for driveways and areas where water tolerance is required *
- Extra strength and durability with a smoother finish
- Tough two-part epoxy compound formula
- Suitable for light commercial and domestic paved areas
- Frost and ice resistance
- 17kg tub
* Not suitable for standard block paving laid unbound with < 5mm joints
EASYJoint PRO is a tough jointing compound for patios, paths and driveways. The two-part epoxy formula provides extra strength and durability with a smoother finish.
Product
Swatches
Sahara
Formally known as Mushroom
Granite
Formally known as Stone Grey
Anthracite
Formally known as Basalt
Installation
Guide
Please note site conditions may vary, as such installation methods will differ.
Before you start – Joints must be at least 3mm wide and 20mm deep.
Recommended tools
A professional grade, variable speed twin-paddle mixer
A hose with adjustable spray nozzle
A rubber or neoprene squeegee
A stiff broom
A coconut fibre broom
Step 1: Soak
Thoroughly pre-soak paving as this helps to reduce residue staining. For porcelain paving material is used, keep the surface damp throughout the installation process.
Step 2: 1st Mix
Remove the activator bottle from the bucket. Replace the lid securely and turn the bucket upside down to release any stuck sand from the bottom. Remove the lid again and mix the sand thoroughly for 1 minute to make sure the sand is completely lump free and flowing.
Step 3: Add the Activator
Empty the contents of the activator bottle into the sand.
Step 4: 2nd Mix
Mix thoroughly until the mixture is free-flowing and has a creamy consistency. This can take between 3 and 5 minutes. Shortcutting this process can seriously affect the outcome of the installation.
Step 5: Pour & Spread
Immediately after mixing, pour the contents of the bucket onto the pre wetted paving. Using the squeegee or broom, move the slurry into the open joints, removing as much compound as possible from the surface.
Step 6: Finish
Use the soft broom to remove any remaining compound off the paving surface, spraying lightly with more water if necessary. Keep the broom damp during this operation.
It is important to sweep the paving as clean as possible to ensure best results.
After the final removal of surplus material, a sheen may be present. This is normal. This generally fades away.
Surfaces may be tacky. Do not attempt to continue washing the surface as this will not help and could affect the final curing of the joint. The tackiness will subside after a few days.
Wash tools in clean water to remove excess product between mixes and after use. Some residue may remain and require a suitable cleaner to completely remove.
Frequently Asked
Questions
EASYJoint PRO is a two-part product where a resin is mixed with coated sand before use. EASYJoint is a single component compound.
EASYJoint PRO can be used on any paving type* however its strength and tolerance to water make it most suitable for driveways, commercial areas, areas with poor drainage and swimming pool terraces.
* Not suitable for standard block paving laid unbound with < 5mm joints
No, a chemical reaction starts once mixed, and the product will harden.
Light rain is not a problem however, prolonged heavy rain may weaken the epoxy and reduce its strength. It is recommended not to use the product if rain is a possibility. Areas should be covered if rain occurs before the product has cured.
Azpects EASYSealer Remover is a high strength stripper which will dissolve the epoxy residue. Care must be taken to avoid damage to surrounding areas including UPVC frames, artificial/real grass and plants when washing off this product.
Yes, a slight sheen may be left, but this will fade over time. Pre-sealing with reduce the amount of residue.
For coverage calculations, please refer to our online calculator here
Unlike standard EASYJoint, EASYJoint PRO does not require any specific site conditions. Once set, the joints are chemical and water tolerant.
Use the prescribed amount as per the in-tub instructions. Using too much water will weaken the epoxy and cause the residue to be sticky.
A slight sheen will be left in most cases, but this is only temporary and will fade. Pre-sealing with reduce the amount of residue.
